American Socket Size Chart

May 18, 2024 Post a Comment

American socket size chart

Six Point Standard Sockets (5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16)

What are the socket sizes in order?

There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).

What size is a 10 mm socket in American?

10mm = just over 3/8 inch. 11mm = almost 7/16 inch. 12mm = almost 15/32 inch (= almost 1/2 inch) 13mm = just over 1/2 inch.

What are the SAE socket sizes?

The most commonly used and sold SAE sizes for wrenches and sockets are:

5/16″
3/8″
7/16″
1/2″
9/16″
5/8″
11/16″
3/4″

What are the 3 common sizes of ratchets?

Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets. Most operate with a geared drive; those with a higher tooth count let you operate the tool with a smaller swinging motion, which is useful when there's little room to move the handle.

What are SAE sockets?

SAE sockets: Society of Automotive Engineers (SAE) sockets are manufactured for work on American-made vehicles. Socket sizes are measured based on imperial system inches and fractions. Some of the commonly used SAE sizes are 3/8 in., 5/8 in., and 11/16 in. sockets.

How do I know what size socket I have?

It's important to note that socket sizes are actually given in two measurements, namely: The size of the drive socket (the part that attaches to the socket wrench). These are always given in imperial measurements, and will usually be either 1/4", 3/8", 1/2", 3/4" or 1".

What is the same as 10mm?

So what is a 10mm socket equivalent? The equivalent imperial size of a 10mm socket is a 3/8 socket. Imperial sizes are known as SAE (Society of Automotive Engineers) or Standard.

What does SAE stand for in tools?

SAE, or standard, is used on most domestic models, while metric applies to foreign or non-domestic vehicles. Socket sets and wrench sets are among the most used tools in cases where size measuring differences are important. Notably, SAE tools are measured in fractions of inches, from 5/32 to 2 ½ inches.

Are m10 and 3/8 the same?

That said, they are very close, the 3/8" bolt is about 0.019" smaller and the pitch's are very close so the 3/8 -16 bolt will thread in the 10mm x 1.5 but the 10 x 1.5 bolt will not fit the 3/8 but..

What does a 10mm socket convert to?

SAE	Metric	Inch
	9mm	0.354
3/8"		0.375
	10mm	0.394
13/32"		0.406

What is a 10mm in standard?

10mm. Little over 3/8 Inch. 0.39370 Inches. 11mm.

Is SAE imperial or metric?

There are two different methods for measuring the hex sizes of sockets. The SAE (Society of Automotive Engineers) system uses inches, and the imperial or metric system uses millimeters.

What does SAE stand for in measurement?

Standard American English and the Metric System Today, measuring in feet and inches is part of the Standard American English (SAE) or Imperial units of measurement, along with volumes like gallons and fluid ounces and weights like pounds.

What size is a 7/8 socket in metric?

Bolt Diameter	Metric	Standard
1/2"	19mm	3/4"
9/16"	21mm	13/16"
	22mm	7/8"
5/8"	24mm	15/16"

Whats bigger 3/8 or 1/4 socket?

3/8 is expressed as 0.375 as a decimal and 1/4 is expressed as 0.25 in its decimal form. It is clear that the value of 3/8 is more than 1/4. Hence, it is bigger.

What are the 4 different types of sockets?

However, some of the commonest options you would find are 36mm sockets and 10mm sockets. Considering the standard sockets, you can find four common types, and they include 3/4 –inch, ½-inch, 3/8-inch, and ¼-inch sockets. Most of these options mentioned above come with bits that would fit Torx screws.

What are 1/4 ratchets used for?

A 1/4-inch ratchet is best for smaller sockets and precision work. The most versatile ratchet is the 3/8-inch size. This ratchet size can accommodate sockets of all sizes. It is big enough to apply a lot of force, but it can still fit into tight spaces.

What are the 3 types of sockets?

Three types of sockets are supported:

Stream sockets allow processes to communicate using TCP. A stream socket provides bidirectional, reliable, sequenced, and unduplicated flow of data with no record boundaries.
Datagram sockets allow processes to use UDP to communicate. ...
Raw sockets provide access to ICMP.

What does AF mean in sockets?

AF Sockets The abbreviation AF means Across Flat (American), this roughly means "measured crosswise" the sockets fit UNF and UNC threads. If the caliper indicates 9/16 "(14.2mm) when measuring the head, you should use a 9/16" socket. So the size of the head is decisive. We sell standard and deep socket sets.