17mm Socket Wrench

There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).

What sizes are in a SAE socket set?

Common SAE socket sizes

• 5/16″
• 3/8″
• 7/16″
• 1/2″
• 9/16″
• 5/8″
• 11/16″
• 3/4″

What are the 3 ratchet sizes?

Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets. Most operate with a geared drive; those with a higher tooth count let you operate the tool with a smaller swinging motion, which is useful when there's little room to move the handle.

What are the different ratchet wrench sizes?

The most common ratchet sizes are ¼ inch drive, 3/8 inch drive, and ½ inch drive. There are also larger ratchet sizes including ¾ inch drive and 1-inch drive available. Most ratchets used with sockets contain a gear mechanism that is designed to allow for rotation in one direction only.

What can I use instead of a socket wrench?

If you don't have a socket wrench, use a box end wrench. If you don't have a box end wrench, use an open end wrench. If you don't have an open end wrench, use an adjustable wrench. If you don't have an adjustable wrench, act like an amateur and use pliers.

How do I know what size socket I have?

It's important to note that socket sizes are actually given in two measurements, namely: The size of the drive socket (the part that attaches to the socket wrench). These are always given in imperial measurements, and will usually be either 1/4", 3/8", 1/2", 3/4" or 1".

Is SAE same as metric?

While the majority of bolt-type fasteners used in the United States conform to one or the other measurement scale, the difference between SAE and metric fasteners (and their corresponding sockets) is as profound as the difference between yards and meters: They are almost the same, but not quite.

Does SAE mean standard?

SAE, or standard, is used on most domestic models, while metric applies to foreign or non-domestic vehicles. Socket sets and wrench sets are among the most used tools in cases where size measuring differences are important. Notably, SAE tools are measured in fractions of inches, from 5/32 to 2 ½ inches.

What does SAE stand for in measurement?

Standard American English and the Metric System Today, measuring in feet and inches is part of the Standard American English (SAE) or Imperial units of measurement, along with volumes like gallons and fluid ounces and weights like pounds.

What are the socket sizes in order?

Six Point Standard Sockets (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1)

What's the difference between a ratchet and a socket wrench?

The main difference here is that, the handle of a regular socket wrench doesn't have the ratcheting mechanism. However, you can get socket wrench set with a ratchet handle. There are various types of sockets available, and most can be attached to a ratchet.

What are the 4 different types of sockets?

However, some of the commonest options you would find are 36mm sockets and 10mm sockets. Considering the standard sockets, you can find four common types, and they include 3/4 –inch, ½-inch, 3/8-inch, and ¼-inch sockets. Most of these options mentioned above come with bits that would fit Torx screws.

What are the 3 types of sockets?

Three types of sockets are supported:

• Stream sockets allow processes to communicate using TCP. A stream socket provides bidirectional, reliable, sequenced, and unduplicated flow of data with no record boundaries.
• Datagram sockets allow processes to use UDP to communicate. ...
• Raw sockets provide access to ICMP.

Are 3/4 and 19mm the same?

19mm = 3/4 inch. 20mm = 25/32 inch. 21mm = just over 13/16 inch. 22mm = almost 7/8 inch.

What is a 3/8 socket in MM?

SAE	Metric	Inch
3/8"		0.375
	10mm	0.394
13/32"		0.406
	11mm	0.433

How do you loosen a nut without a socket wrench?

Nuts. Method 3 find yourself a zip tie. And do the same step is method 1 with the duct tape but

Can you use a wrench instead of socket wrench?

A wrench with an open end fits around a fastener instead of over it, so you can slip it into an area where there isn't room for a socket. Always make sure the tool you use is suited for the work you're doing.

What do you do if your wrench is too big?

- Use a coin, or combination of coins, to fill the gap between the nut or bolt and the too-large wrench. - Try different combinations of coins to make the wrench as snug to the nut or bolt as possible, since the better the fit is the less likely the wrench is to slip off.

What is most common size socket wrench?

The most commonly used types are 8 mm, 10 mm and 14 mm sockets.

What is a 18mm socket in standard?

That size socket would fall between a 11/16 in and 3/4 in.